Skip to content

Plastering is an activity that requires a lot of practice, effort, and time. Thus, plastering your ceiling can be a daunting task if you don’t have adequate experience.

The article will provide you with insight on the right tools for ceiling plastering, the simple steps, and the tricks on how you can go about it.

Plastered wall and ceiling recently done in Bendigo

Plastering

Tools and Equipment Needed

You need to gather all the equipment that you will use when plastering your ceiling. These tools are;

  • Plastering trowel
  • Plaster
  • Sandpaper
  • Ladder
  • Water and sponge
  • Mixing stick
Step by Step Guideline on Plastering your Ceiling

Latest plastered ceiling in Bendigo

You can rescue or repair the ceiling of your house from additional damages. The following are the steps you can follow when plastering the ceiling.

Prepare the Room

Preparing the surface entails removing the furniture from the room you are going to plaster to avoid spilling the wet plaster on them.

Plastering the ceiling is a hard task because it requires balancing of the ladder and the wet platter. Thus it is likely that there will be some dripping on the surface below the ceiling.

Therefore, it’s essential to remove the furniture or cover the few items that may remain as well as the floor. Failure to the plaster can fall and harden on the floor or your furniture.

You should also protect yourself by wearing some old clothes that you don’t mind staining and renovation mask.

Prepare the Ceiling

Most ceilings have uneven patches that need to be levelled first. Otherwise, these defects will be visible in the new ceiling. That means you should dust the oil ceiling using sandpaper, vacuum it afterwards to remove cobwebs and wipe it clean with a sponge or cloth and soapy water. Rinse the ceiling with a sponge and clean water. You can also use a degreaser to remove oil from the ceiling because the plaster won’t hold on an oily surface. Further, you should fix any cracks and holes in the ceiling first before plastering.

Fixing a Hole in the Ceiling:
  • A hole can compromise your project when not handled properly. Thus, you should begin by brushing the surface around the hole to loosen any particles around its edge.
  • Fill the hole with the plaster, apply the first coat, and cover it with wire mesh to make it secure.
  • Apply the second coat on top of the mesh and snip off the exposed part of the wire that didn’t stick when the plaster dried.
  • You can use sandpaper to smoothen the edges of the hole and make it even like the rest of the ceiling.
Mix the Plaster

The ratio of water and plaster should be 1:1. Thus add the plaster to water and mix the two using a mixing stick until you get a consistent mixture.

Begin Plastering the Ceiling

The first step is to make safety your priority. Thus ensure that you have the renovation helmet and the ladder is well set. Having a second person in the room is an added advantage. Begin by dividing the ceiling into different portions, then dab the ceiling with some water to wet the surface. When the background is high suction porous, then it will absorb the moisture in the plaster first thus, forcing it to dry very fast. Apply the first coat or skim coat on the entire ceiling. Make sure that the trowel starts with its one side angled away from it. Apply the second coat using the skim coat technique. Therefore, the two layers of plaster should contribute to an even and smooth ceiling.

Smooth It Out

It’s expected that the ceiling will have some bumps that need to be removed using sandpaper. The ceiling is now ready for a coat of paint.

Plastering Tips and Tricks
  • You should apply plaster on a clean surface; thus, you should remove any dust, existing plaster, and wallpaper before starting this project. Otherwise, the plaster won’t stick.
  • An electric mixer will give you a consistent mixture. Don’t over mix the plaster because it will make it go off quickly.
  • Thick mixes are suitable for uneven and Artex surfaces, while the lighter combination is suitable for flat surfaces and plasterboard.
  • You can use a mist spray gun when wetting the ceiling before applying the first coat of plaster. This will save you time instead of going down to wet your brush. Wet the surface until the water starts to drip to control the suction.
  • Adding sand on the mixture is important because it gives it a better adhesion and rougher texture.
  • Use a trowel to flatten and remove any lines after the first coat of plaster.
  • You should flick the ceiling with some water using your brush as the plaster begins to firm up.
  • Make sure that all the edges around the skirting boards and the walls are filled.
  • Don’t struggle with making the first coat perfect. It will take more time to make this space smooth.
  • Clean your equipment as you continue to avoid contaminating your plaster.
  • You should always add plaster to the water and not the other way round.
  • Both water and plaster should be mixed at a ratio of 1:1, and in the end, you should have a bucket full of plaster.
The cost of plastering a ceiling

The cost of plaster is determined by the overall state of repair and the size of the ceiling. Therefore, it’s expensive to plaster more substantial ceilings than smaller ones. This is because you need more materials and it will take longer.

It is expensive to plaster a rough ceiling with small holes than it is to work on a smooth one. You can get the precise cost of plastering your ceiling by contacting the Bendigo Plastering Service. The company will is a licensed and professional plaster that will give your ceiling an elegant and stylish look.

You must realize that plasters are popular for wall and ceiling finish, and it will continue. Thus, give your ceiling a perfect plastering finish.

Need plastering services? Contact us 0491 641 345 or email us at [email protected]

 

Leave a Comment